What are you looking for?
Bronkhorst
Datasheet M13V14I

mini CORI-FLOW™ M13V14I

Low Flow Coriolis Mass Flow Controller

  • High accuracy, excellent repeatability
  • Fast response
  • Independent of fluid properties
  • Additional density and temperature output
  • Compact, rugged (IP65) design
  • Optional ATEX approval Cat.3, Zone 2
お見積り依頼 Downloads Datasheet
mini CORI-FLOW™M13V14I

Low Flow Coriolis Mass Flow Controllers for Liquids

mini CORI-FLOW™ Mass Flow Meters and Controllers are precise and compact instruments, based on the Coriolis measuring principle, designed to cover the needs of the low flow market. Bronkhorst® model M13V14I Mass Flow Controller (MFC) is suited for highly accurate control of liquid flow in the range of 0…2000 g/h at operating pressures up to 100 bar (higher on request). The instruments are equipped with a robust IP65 weatherproof housing and are optionally available with ATEX approval for use in Zone 2 hazardous areas.

The instrument contains a microprocessor based pc-board with signal and fieldbus conversion and a PID controller for mass flow control by means of an integrated control valve (normally closed).

Technical specifications

Measurement / control system
流量レンジ0…2000 g/h (nominal flow rate: 1000 g/h);
Full Scale (FS) value is user-configurable;
advised minimum flow depends on fluid properties
Mass flow accuracy± 0,2 % Rd
Repeatability± 0,05 % of rate ± ½(ZS* x 100/actual flow)%
Turndown ratio≥ 1:50
Zero stability (ZS)< ± 0,2 g/h
(Guaranteed at constant temperature and for unchanging process and environment conditions.)
Settling time (in control, typical)1 sec. (typical)
Temperature effecton zero: < 0,02 g/h/°C;
on span: < 0,001% Rd/°C;
self heating (at zero flow): < 15°C
(Depends on flow rate, heat capacity fluid, T amb., T fluid and cooling capacity.)
Operating temperature0 … 70 °C ;
for ATEX Cat.3, Zone 2 max. 50°C
Mountingany position, attitude sensitivity negligible.
Instrument to be rigidly bolted to a stiff and heavy mass or construction for guaranteed zero stability.
External shocks or vibrations should be avoided.
Temperature accuracy± 0,5 °C
Density accuracy< ± 5 kg/m³ (at full scale flow)
Max. Kv-value2,4 x 10-3
Max. fluid viscosity0,1 Pa*s
Leak integrity, outboardtested < 2 x 10-9 mbar l/s He
Warm-up time> 30 min for optimum accuracy
Mechanical parts
Sensorsingle tube, DN 0.5
Valve seatKalrez®-6375, other on request
Material (wetted parts)stainless steel 316L or comparable
Housingstainless steel 430F
Pressure rating (PN)100 bar abs
Process connectionscompression type or face seal (VCR/VCO) couplings, or Tri-Clamp flanges (welded)
Purge connection1/8” OD compression type or 1/8" VCR
Sealsmetal
Weight1,5 kg
Ingress protectionIP65 (weatherproof)
Electrical properties
Power supply+15…24 Vdc +/- 10%
Max. ripple recommended: 50 mV tt
Max. power consumptionmax. 7 W
Analog output0…5 (10) Vdc, min. load impedance > 2 kΩ;
0 (4)…20 mA (sourcing), max. load impedance < 375 Ω
Analog setpoint0…5 (10) Vdc, min. load impedance > 100 kΩ;
0 (4)…20 mA (sourcing), max. load impedance ~ 250 Ω
Digital communicationstandard: RS232;
options: PROFIBUS DP, DeviceNet™, Modbus RTU or FLOW-BUS
Electrical connection
Analog/RS2328-pin DIN (male);
PROFIBUS DPbus: 5-pin M12 (female);
power: 8-pin DIN (male);
CANopen® / DeviceNet™5-pin M12 (male);
FLOW-BUS/Modbus-RTU/ASCII 5-pin M12 (male);
Control valve options
External actuator options to be connected to the controller
Certification for hazardous areas
Approvals / certificates

Technical specifications subject to change without notice.

For dimensional drawings and hook-up diagrams please visit the product page on our website

Downloads

Brochures
mini CORI-FLOW M12-M14 brochure
CORI-FILL brochure
Manuals
MINI CORI-FLOW Manual
Certificates
ATEX: KEMA 10ATEX0111X
Hook-up diagrams
Analog I-O RS232
DeviceNet
FLOW-BUS
Modbus
PROFIBUS DP
Dimensional drawings
Meters - compression type weld adapters
Meters - VCR type machined adapters
Controllers - compression type weld adapters
Controllers - VCR type machined adapters
C5I Controllers - compression type weld adapters
C2I Controllers - compression type weld adapters
Controllers - on a 2 kg mass block
Controllers - on a 4 kg mass block
Dimensions Weld Adapters
Solids 3D
M12V14I-M13V14I-M14V14I 1-4VCR
M12V14I-M13V14I-M14V14I excl. adapters
Mass block mini Cori-Flow Mxx 2kg
Mass block mini Cori-Flow Mxx 4kg
M13V14I MFC 6mm compr.type
Download as PDF
ブロンコスト・ジャパン株式会社
〒135-0016
東京都江東区東陽5-27-5
Tel.  03-3645-1371

sales◎bronkhorst.jp   ◎を@に置き換えて下さい

     
Copyright © 2024 Bronkhorst. All rights reserved.     サイトマップ     免責事項     プライバシーポリシー

Bronkhorst High-Tech designs and manufactures innovative instruments and subsystems for low-flow measurement and control for use in laboratories, machinery and industry. Driven by a strong sense of sustainability and with many years of experience, we offer an extensive range of (mass) flow meters and controllers for gases and liquids, based on thermal, Coriolis and ultrasonic measuring principles. Our global sales and service network provides local support in more than 40 countries. Discover Bronkhorst®!